下面是stc串口测试程序,供你参考,协议你自己编把,按键需要软件做消抖处理,led简单,如果你不会写led就不要搞这个了
#include
#include
sfr S2CON = 0x9A;
//S2SM0,S2SM1,S2SM2,S2REN,S2TB8,SRB8,S2TI,S2RI
sfr IE2 = 0xAF;
//X,X,X,X,X,X,ESPI,ES2
sfr S2BUF = 0x9B;
sfr AUXR = 0x8e;
sfr BRT = 0x9c;
sfr IAP_CONTR = 0xC7;
sfr CCON = 0xD8;
sfr CMOD = 0xD9;
sfr CL = 0xE9;
sfr CH = 0xF9;
sfr CCAP0L = 0xEA;
sfr CCAP0H = 0xFA;
sfr CCAPM0 = 0xDA;
sfr CCAPM1 = 0xDB;
sbit CR = 0xDE;
sbit MCU_Start_Led = P1^7;
sbit S2_Interrupt_Receive_Led = P1^4;
//unsigned char self_command_array[4] = {0x22,0x33,0x44,0x55};
#define Self_Define_ISP_Download_Command 0x22
#define RELOAD_COUNT 0xfb //18.432MHz,12T,SMOD=0,9600bps
void serial_port_one_initial();
void send_UART_one(unsigned char);
void UART_one_Interrupt_Receive(void);
void serial_port_two_initial();
void send_UART_two(unsigned char);
void UART_two_Interrupt_Receive(void);
void soft_reset_to_ISP_Monitor(void);
void delay(void);
void display_MCU_Start_Led(void);
void send_PWM(void);
void main(void)
{
unsigned int array_point = 0;
unsigned char xdata Test_array_one[512] =
{
0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17,
0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f,
0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27,
0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f,
0x30, 0x31, 0x32, 0x33, 0x34, 0x35, 0x36, 0x37,
0x38, 0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f,
0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,
0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f,
0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57,
0x58, 0x59, 0x5a, 0x5b, 0x5c, 0x5d, 0x5e, 0x5f,
0x60, 0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67,
0x68, 0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f,
0x70, 0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77,
0x78, 0x79, 0x7a, 0x7b, 0x7c, 0x7d, 0x7e, 0x7f,
0x80, 0x81, 0x82, 0x83, 0x84, 0x85, 0x86, 0x87,
0x88, 0x89, 0x8a, 0x8b, 0x8c, 0x8d, 0x8e, 0x8f,
0x90, 0x91, 0x92, 0x93, 0x94, 0x95, 0x96, 0x97,
0x98, 0x99, 0x9a, 0x9b, 0x9c, 0x9d, 0x9e, 0x9f,
0xa0, 0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa6, 0xa7,
0xa8, 0xa9, 0xaa, 0xab, 0xac, 0xad, 0xae, 0xaf,
0xb0, 0xb1, 0xb2, 0xb3, 0xb4, 0xb5, 0xb6, 0xb7,
0xb8, 0xb9, 0xba, 0xbb, 0xbc, 0xbd, 0xbe, 0xbf,
0xc0, 0xc1, 0xc2, 0xc3, 0xc4, 0xc5, 0xc6, 0xc7,
0xc8, 0xc9, 0xca, 0xcb, 0xcc, 0xcd, 0xce, 0xcf,
0xd0, 0xd1, 0xd2, 0xd3, 0xd4, 0xd5, 0xd6, 0xd7,
0xd8, 0xd9, 0xda, 0xdb, 0xdc, 0xdd, 0xde, 0xdf,
0xe0, 0xe1, 0xe2, 0xe3, 0xe4, 0xe5, 0xe6, 0xe7,
0xe8, 0xe9, 0xea, 0xeb, 0xec, 0xed, 0xee, 0xef,
0xf0, 0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7,
0xf8, 0xf9, 0xfa, 0xfb, 0xfc, 0xfd, 0xfe, 0xff,
0xff, 0xfe, 0xfd, 0xfc, 0xfb, 0xfa, 0xf9, 0xf8,
0xf7, 0xf6, 0xf5, 0xf4, 0xf3, 0xf2, 0xf1, 0xf0,
0xef, 0xee, 0xed, 0xec, 0xeb, 0xea, 0xe9, 0xe8,
0xe7, 0xe6, 0xe5, 0xe4, 0xe3, 0xe2, 0xe1, 0xe0,
0xdf, 0xde, 0xdd, 0xdc, 0xdb, 0xda, 0xd9, 0xd8,
0xd7, 0xd6, 0xd5, 0xd4, 0xd3, 0xd2, 0xd1, 0xd0,
0xcf, 0xce, 0xcd, 0xcc, 0xcb, 0xca, 0xc9, 0xc8,
0xc7, 0xc6, 0xc5, 0xc4, 0xc3, 0xc2, 0xc1, 0xc0,
0xbf, 0xbe, 0xbd, 0xbc, 0xbb, 0xba, 0xb9, 0xb8,
0xb7, 0xb6, 0xb5, 0xb4, 0xb3, 0xb2, 0xb1, 0xb0,
0xaf, 0xae, 0xad, 0xac, 0xab, 0xaa, 0xa9, 0xa8,
0xa7, 0xa6, 0xa5, 0xa4, 0xa3, 0xa2, 0xa1, 0xa0,
0x9f, 0x9e, 0x9d, 0x9c, 0x9b, 0x9a, 0x99, 0x98,
0x97, 0x96, 0x95, 0x94, 0x93, 0x92, 0x91, 0x90,
0x8f, 0x8e, 0x8d, 0x8c, 0x8b, 0x8a, 0x89, 0x88,
0x87, 0x86, 0x85, 0x84, 0x83, 0x82, 0x81, 0x80,
0x7f, 0x7e, 0x7d, 0x7c, 0x7b, 0x7a, 0x79, 0x78,
0x77, 0x76, 0x75, 0x74, 0x73, 0x72, 0x71, 0x70,
0x6f, 0x6e, 0x6d, 0x6c, 0x6b, 0x6a, 0x69, 0x68,
0x67, 0x66, 0x65, 0x64, 0x63, 0x62, 0x61, 0x60,
0x5f, 0x5e, 0x5d, 0x5c, 0x5b, 0x5a, 0x59, 0x58,
0x57, 0x56, 0x55, 0x54, 0x53, 0x52, 0x51, 0x50,
0x4f, 0x4e, 0x4d, 0x4c, 0x4b, 0x4a, 0x49, 0x48,
0x47, 0x46, 0x45, 0x44, 0x43, 0x42, 0x41, 0x40,
0x3f, 0x3e, 0x3d, 0x3c, 0x3b, 0x3a, 0x39, 0x38,
0x37, 0x36, 0x35, 0x34, 0x33, 0x32, 0x31, 0x30,
0x2f, 0x2e, 0x2d, 0x2c, 0x2b, 0x2a, 0x29, 0x28,
0x27, 0x26, 0x25, 0x24, 0x23, 0x22, 0x21, 0x20,
0x1f, 0x1e, 0x1d, 0x1c, 0x1b, 0x1a, 0x19, 0x18,
0x17, 0x16, 0x15, 0x14, 0x13, 0x12, 0x11, 0x10,
0x0f, 0x0e, 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08,
0x07, 0x06, 0x05, 0x04, 0x03, 0x02, 0x01, 0x00
};
unsigned char i = 0;
serial_port_one_initial(); //串口1初始化
// serial_port_two_initial(); //串口2初始化
display_MCU_Start_Led(); //点亮发光二极管表示单片机开始工作
// send_UART_two(0x55); //串口2发送数据表示单片机串口正常工作
// send_UART_two(0xaa); //串口2发送数据表示单片机串口正常工作
/*
for(array_point=0; array_point<512; array_point++)
{
send_UART_two(Test_array_one[array_point]);
}
*/
send_UART_one(0x34); //串口1发送数据表示单片机串口正常工作
send_UART_one(0xa7); //串口1发送数据表示单片机串口正常工作
for(array_point=0; array_point<512; array_point++)
{
send_UART_one(Test_array_one[array_point]);
}
// send_PWM(); //6kHz PWM, 50% duty
while(1);
}
void serial_port_one_initial()
{
SCON = 0x50; //0101,0000 8位可变波特率，无奇偶校验位
// TMOD = 0x21; //0011,0001 设置顶时器1为8位自动重装计数器
// TH1 = RELOAD_COUNT; //设置定时器1自动重装数
// TL1 = RELOAD_COUNT;
// TR1 = 1; //开定时器1
BRT = RELOAD_COUNT;
// BRTR = 1, S1BRS = 1, EXTRAM = 1 ENABLE EXTRAM
AUXR = 0x11; // T0x12,T1x12,UART_M0x6,BRTR,S2SMOD,BRTx12,EXTRAM,S1BRS
ES = 1; //允许串口中断
EA = 1; //开总中断
}
void serial_port_two_initial()
{
//sfr SCON = 0x98;
//SM0,SM1,SM2,REN,TB8,RB8,TI,RI
//sfr S2CON = 0x9A;
//S2SM0,S2SM1,S2SM2,S2REN,S2TB8,S2RB8,S2TI,S2RI
//sfr S2BUF = 0x9B;
//sfr IE2 = 0xAF;
//X,X,X,X,X,X,ESPI,ES2
S2CON = 0x50; //0101,0000 8位可变波特率，无奇偶校验位,允许接收
BRT = RELOAD_COUNT;
// BRTR = 1, S1BRS = 1, EXTRAM = 0 ENABLE EXTRAM
AUXR = 0x11; // T0x12,T1x12,UART_M0x6,BRTR,S2SMOD,BRTx12,EXTRAM,S1BRS
// ES = 1; //允许串口1中断
// ES2 = 1
IE2 = 0x01; //允许串口2中断,ES2=1
EA = 1; //开总中断
}
void send_UART_one(unsigned char i)
{
ES = 0; //关串口中断
TI = 0; //清零串口发送完成中断请求标志
SBUF = i;
while(TI ==0); //等待发送完成
TI = 0; //清零串口发送完成中断请求标志
ES = 1; //允许串口中断
}
void send_UART_two(unsigned char i)
{
//sfr SCON = 0x98;
//SM0,SM1,SM2,REN,TB8,RB8,TI,RI
//sfr S2CON = 0x9A;
//S2SM0,S2SM1,S2SM2,S2REN,S2TB8,S2RB8,S2TI,S2RI
//sfr S2BUF = 0x9B;
//sfr IE2 = 0xAF;
//X,X,X,X,X,X,ESPI,ES2
unsigned char temp = 0;
// ES = 0; //关串口1中断
IE2 = 0x00; //关串口2中断,es2=0
// TI = 0; //清零串口1发送完成中断请求标志
S2CON = S2CON & 0xFD; //B'11111101,清零串口2发送完成中断请求标志
// SBUF = i;
S2BUF = i;
// while(TI ==0); //等待发送完成
do
{
temp = S2CON;
temp = temp & 0x02;
}while(temp==0);
// TI = 0; //清零串口发送完成中断请求标志
S2CON = S2CON & 0xFD; //B'11111101,清零串口2发送完成中断请求标志
// ES = 1; //允许串口1中断
// ES2 = 1
IE2 = 0x01; //允许串口2中断,ES2=1
}
void UART_one_Interrupt_Receive(void) interrupt 4
{
unsigned char k = 0;
if(RI==1)
{
RI = 0;
k = SBUF;
if(k==Self_Define_ISP_Download_Command) //是自定义下载命令
{
delay(); //延时1秒就足够了
delay(); //延时1秒就足够了
soft_reset_to_ISP_Monitor(); //软复位到系统ISP监控区
}
send_UART_one(k+1);
}
else
{
TI = 0;
}
}
void UART_two_Interrupt_Receive(void) interrupt 8
{
//sfr SCON = 0x98;
//SM0,SM1,SM2,REN,TB8,RB8,TI,RI
//sfr S2CON = 0x9A;
//S2SM0,S2SM1,S2SM2,S2REN,S2TB8,S2RB8,S2TI,S2RI
//sfr S2BUF = 0x9B;
//sfr IE2 = 0xAF;
//X,X,X,X,X,X,ESPI,ES2
unsigned char k = 0;
k = S2CON ;
k = k & 0x01;
//if(S2RI==1)
if(k==1)
{
//RI = 0;
S2CON = S2CON & 0xFE; //1111,1110
S2_Interrupt_Receive_Led = 0;
k = S2BUF;
if(k==Self_Define_ISP_Download_Command) //是自定义下载命令
{
delay(); //延时1秒就足够了
delay(); //延时1秒就足够了
soft_reset_to_ISP_Monitor(); //软复位到系统ISP监控区
}
send_UART_two(k+1);
}
else
{
//TI = 0;
S2CON = S2CON & 0xFD; //1111,1101
}
}
void soft_reset_to_ISP_Monitor(void)
{
IAP_CONTR = 0x60; //0110,0000 软复位到系统ISP监控区
}
void delay(void)
{
unsigned int j = 0;
unsigned int g = 0;
for(j=0;j<5;j++)
{
for(g=0;g<60000;g++)
{
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
}
}
}
void display_MCU_Start_Led(void)
{
//sbit MCU_Start_Led = P1^7;
unsigned char i = 0;
for(i=0;i<1;i++)
{
MCU_Start_Led = 0; //顶亮MCU开始工作指示灯
delay();
MCU_Start_Led = 1; //熄灭MCU开始工作指示灯
delay();
MCU_Start_Led = 0; //顶亮MCU开始工作指示灯
}
}
void send_PWM(void)
{
CMOD = 0x00; // CIDL - - - - CPS1 CPS0 ECF Setup PCA Timer
// CPS1 CPS0 = 00, Fosc/12 is PCA/PWM clock
// 18432000/12/256 = 6000
CL = 0x00;
CH = 0x00;
CCAP0L = 0x80; //Set the initial value same as CCAP0H
CCAP0H = 0x80; //50% Duty Cycle
CCAPM0 = 0x42; //0100,0010 Setup PCA module 0 in 8BIT PWM, P3.7
CR = 1; //启动 PCA/PWM 定时器
}
单片机1 接4按键。
单片机2 接8个发光二极管。
当按下某一个按键时，对应的发光二级管亮，对应规则不限。
按照这个要求，仅仅需要传送四位数。
这么简单，就没有必要弄什么规则了，也几乎没有办法弄规则。 追问恩是的。直接发送给sbuf赋值，接受sbuf取值就可以。
但是我用232无线模块，就是发送明码的那种模块，相当于串口无线延长线。简单的通信好像有码丢失，老出错。就想自定义一组数据带识别码。但是不会写谢谢指导。可以追加分的。
回答其实不难写，但是未必能一次性达到要求，难免修改几次。
还是留下邮箱吧。
追问恩。谢谢。邮箱 495440210@qq.com
回答邮件已经发了。
单片机1 接4按键。
单片机2 接8个发光二极管。
当按下某一个按键时，对应的发光二级管亮，对应规则不限。
按照这个要求，仅仅需要传送四位数。
这么简单，就没有必要弄什么规则了，也几乎没有办法弄规则。
这个事情你还是花钱请人帮你吧，要别人直接给你写程序，还是免了吧。你给200元我可以花一个小时帮你做写。
建议 去 我的领地 5d6d 的 proteus 论坛看看
那里有很多 单片机仿真实例，包括仿真图 和 源码
搜 5d6d 和 proteus 2个关键词
内容全部来源于网络收集，如有侵权，请联系网站删除：QQ：24596024